Samsung and Dash are pushing the brand new Android 6.zero.1 Marshmallow official OTA Updates for all Galaxy J7 SM-J700P fashions.
If you wish to discover ways to efficiently flash the brand new firmware, then you ought to be checking the data listed on this submit.
Android 6.zero.1 Marshmallow updates are being rolled out over the air in levels, which signifies that not all makes use of are going to get the firmware bump concurrently others. For those who don’t need to wait till Dash releases the brand new replace in your area, then you possibly can manually flash it utilizing the ODIN app.
Earlier than beginning set up it’s worthwhile to examine the rules under:
- use the tutorial just for the Dash mannequin of the Samsung Galaxy J7 units.
– your telephone’s mannequin needs to be SM – J700P and you have to be on Dash community.
– don’t try and replace different totally different Samsung Galaxy J7 fashions. - you’ll be able to verify your telephone’s mannequin quantity underneath Settings> About Telephone part.
- obtain and set up the Samsung USB Drivers in your PC from here.
– the usb drivers will assist you to join the telephone with the PC. - for the updating course of you’ll need to make use of the Odin app, and Odin requires the next issues so as to have the ability to flash the replace:
– you have to set up the Samsung USB drivers above.
– the ODIN app additionally wants for the USB Debugging to be enabled in your telephone’s Developer Choices.
– in the event you can’t discover Developer Choices you must allow it: go to Settings> About Telephone and faucet 7 occasions on the Construct Quantity part.
– return to Settings, scroll down and open Developer Choices.
– Open Developer Choices, allow it, then search for USB Debugging to allow it, too. - you’ll be able to flash the brand new replace over rooted firmware, too, however you’ll lose root entry within the course of.
– any customized Restoration you may need put in goes to get replaced with a inventory Restoration picture. - the brand new official replace could be flashed over customized ROMs, however it is advisable to manufacturing unit reset the system partition after the replace is completed.
– the manufacturing unit reset steps are listed on the finish of this publish.
– manufacturing unit resetting the system goes to take away the system partition and the customized ROM.
– the manufacturing unit reset gained’t take away any knowledge from the interior storage of your gadget. - in case your telephone is operating 100% inventory Android then you will get to the subsequent a part of this submit proper now, as no information shall be misplaced within the course of.
- this can be a tutorial that must be utilized by superior customers solely.
- we can’t be blamed in case you brick the telephone nor in case you lose any knowledge within the course of.
- verify battery cost degree of your telephone and be sure that there’s no less than 50% energy left earlier than it switches off.
Now that you simply’ve learn all of the above you will get to the subsequent a part of this publish.
Learn how to flash Android 6.zero.1 Marshmallow Replace for Samsung Galaxy J7 Dash:
- Obtain the Android 6.zero.1 Marshmallow replace archive file from here.
- When the obtain is completed it’s essential extract the archived contents.
– you’ll get hold of the J700PVPU1APF3 tar.md5 firmware file.
– don’t unzip the tar.md5 file, as that’s the replace file it’s essential to load and flash with Odin. - Obtain Odin three.10.7 from here.
– unzip Odin contents. - Energy off the telephone.
- Boot it in Obtain Mode.
– Quantity Down + Residence + Energy buttons on the similar time.
– launch the buttons when the Warning display load, then press Quantity As much as affirm Obtain Mode boot. - Open the Odin exe in your pc.
- Join the telephone to PC by way of usb cable.
– watch for Odin to detect the gadget, then get to the subsequent step.
– if no gadget is detected you have to attempt to reinstall Samsung usb drivers as soon as extra. - Get again to Odin’s important window and open the OPTIONS tab. Be sure that ‘re-partition’ is disabled.
– don’t edit different totally different Odin choices. - Subsequent, click on AP button in ODIN. You have to load the brand new firmware replace file.
- Discover and cargo the J700PVPU1APF3 tar.md5 updating file in Odin.
- Hit START to start the Android 6.zero.1 replace in your Dash Galaxy J7 system.
- When the set up is completed you possibly can see the telephone rebooting in regular mode and the PASS alert proven by ODIN.
– notice that the primary boot strategy of this new Android 6.zero.1 OS goes to take some time earlier than it masses all the brand new information. - Unplug the telephone from PC when the ‘optimizing apps’ display masses in your gadget.
I hope that you simply’ve managed to finish the set up of Android 6.zero.1 Marshmallow in your Galaxy J7 Dash telephone.
If the FAIL alert is proven by ODIN or in case you’re proven any errors earlier than the set up is completed, then you will have to attempt to repeat the entire tutorial greater than as soon as.
In case you repeat set up you want to ensure that your telephone meets all necessities and that you simply gained’t be skipping any steps listed above.
Word:
If the PASS alert is displayed in Odin, however your Galaxy J7 Dash telephone enters in a boot loop or it will get caught on the boot animation display, then you will have to attempt to ‘manufacturing unit reset’ the gadget.
The Manufacturing unit Reset course of needs to be utilized in case you’ve put in the brand new Android 6.zero.1 Replace over a customized ROM, too. Right here’s tips on how to manufacturing unit reset your gadget:
- energy off the telephone.
- boot it in Restoration Mode.
– Quantity UP + Residence + Energy on the similar time. - choose ‘wipe knowledge/ manufacturing unit reset’ choice from the Restoration choices.
- affirm course of.
- reboot your telephone in regular mode when finished with this tutorial.